• Predicting energy absorption parameters of aluminum lattice structures filled tubes via artificial neural networks 

  Çetin, Erhan; Baykasoğlu, Cengiz; Baykasoğlu, Adil (2019)

  In this paper, the energy absorption parameters of aluminum body centered cubic lattice structures filled thin-walled tubes under axial loading are predicted via artificial neural networks (ANNs). Different tube thickness, ...

• Kafes yapı dolgulu hibrit tüplerin enerji sönümleme performanslarının sonlu elemanlar yöntemi kullanılarak incelenmesi 

  Çetin, Erhan; Baykasoğlu, Cengiz (2019)

  İnce cidarlı tüplerin enerji sönümleme performanslarının iyileştirmesine yönelik literatürde birçok farklı yaklaşım önerilmiştir. Bu bağlamda farklı tipte malzemeler, kesit geometrileri, desenler vb. önerilmiş ve bu yapıların ...

• Yönlendirilmiş enerji bırakımlı eklemeli imalat süreçlerinde meydana gelen metalurjik faz dönüşümlerinin sonlu elemanlar yöntemi kullanılarak benzetilmesi 

  Baykasoğlu, Cengiz; Akyıldız, Öncü; Tunay, Merve (2019)

  Son yıllarda popülerlik kazanmış olan eklemeli imalat teknolojileri kullanılarak önceden imalatı veya tamiri oldukça zor veya imkânsız olan yapısal parçalar metalik, seramik, polimer ve karma malzemeler kullanılarak imal ...

• Investigation of the effect of temperature on the mechanical properties of E-Glass fiber reinforced composites 

  Haboğlu, Mustafa Reşit; Kurşun, Ali; Kara, Emre; Çetin, Erhan; Aykul, Halil (The Composites and Advanced Materials Expo (CAMX), 2014)

  In this study, mechanical characterization of E-Glass fiber reinforced composite materials that are manufactured via Vacuum Infusion (VI) (a.k.a Vacuum Assisted Resin Transfer Molding (VARTM)) is investigated. The mechanical ...

• Performance investigation of an eight cylinder gasoline engine 

  Kılıçarslan, Ali; Qatu, Mohamad S. (American Society of Mechanical Engineers (ASME), 2014)

  Performance investigation of a Chevrolet 5.7, eight cylinder gasoline engine is experimentally carried out at laboratuary conditions by means of the special softwares called "NetDyn" and "WinDyn". This experimental work ...

• Low velocity impact response of glass fiber reinforced aluminium foam sandwich 

  Kara, Emre; Crupi, Vincenzo; Epasto, Gabriella; Guglielmino, Eugenio; Aykul, Halil (European Conference on Composite Materials, ECCM, 2012)

  The aim of this study was the analysis of the bending and the low - velocity impact response of aluminium foam sandwich reinforced by the outer skins made of glass fiber reinforced epoxy matrix and the results were compared ...

• Investigation of irreversibilities in the compression process for alternative refrigerants in a vapor compression refrigeration cycle 

  Kılıçarslan, Ali; Müller, Norbert (2008)

  Irreversibility analyses during compression process are presented for some refrigerants namely, R290, R134a, R12, R22, and R152a in a vapor compression refrigeration cycle. The effects of evaporator temperature, condenser ...

• Design of sma based actuators used in robotics 

  Öztürk, Muhammet; Koçer, Bahadır; Uygun, Recep (2013)

  This work introduces to Shape Memory Alloy (SMA) using in Robotics as actuators. We investigated a quadruped platform actuated by SMAs which act with variable elasticity. SMAs ought to prove necessary forces for all gaits. ...

• Investigation of experimental research on the low velocity impact damage behavior of NCF composite plates - Complas XII 

  Ağır, İnan; Kurşun, Ali; Bektaş, Numan Behlül (2013)

  In this study an experimental investigation is performed on the impact response of non-crimp fabric composite plates at room temperature. Chopped strand mat combi is used as reinforcing material and two kinds of matrix; ...

• Elastoplastic stress analysis of functionally graded disc under internal pressure-complas XII 

  Kurşun, Ali; Ağır, İnan; Topçu, Muzaffer (2013)

  The study deals with elastoplastic stress analysis of a hollow disk made of functionally graded materials (FGMs) subjected to an internal pressure. The material properties of disc are assumed to vary radially according to ...

• Determination of noise level of a gas-fired pulse combustor 

  Kılıçarslan, Ali; Arısoy, Ahmet (2007)

  Experimental determination of noise level of a Helmholtz type gas-fired pulse combustor is presented. During the tests, the tail pipe length was varied from 1.9 m to 1.3 m by 10 cm intervals. Noise level measurements were ...

• Monitoring and control of PLC based motion control systems via device-net 

  Işık, Mehmet Fatih; Haboğlu, Mustafa Reşit; Yanmaz, Hilmi (Institute of Electrical and Electronics Engineers Inc., 2014)

  The control of mechanical systems are generally applied by using electric motors which are useful for the control of velocity, position and torque. On the other hand, servo motors are preferred due to their characteristic ...

• Irreversibility analysis of a vapor compression cascade refrigeration cycle 

  Kılıçarslan, Ali; Müller, Norbert (2009)

  Hydrocarbon based energy sources such as coal, oil and natural gas have been diminishing in an increasing speed. Instead of finding alternative energy sources, we have to use the available sources more effectively. By means ...

• Physical properties of LLDPE and PP filled with wood flours 

  Baş, Gamze Sultan; Sancaktar, Erol; Karadurmuş, Erdal (American Society of Mechanical Engineers (ASME), 2015)

  In this study, composites of polypropylene (PP), as well as linear low density polyethylene (LLDPE) thermoplastics filled with wood flour have been investigated to study the effect of size and amount of wood flour on their ...

• Energy and exergy analysis of an air conditioning system using the mixture of outdoor and return air 

  Kılıçarslan, Ali; Kurtbaş, İrfan (2012)

  Energy and exergy analysis of the air conditioning systems employing the mixture of outdoor and return air (ACOR) are presented. The equations of heat transfer rate and exergy destruction are developed for ACOR according ...

• Stress analysis of a rotating FGM circular disc with exponentially-varying properties 

  Kurşun, Ali; Topçu, Muzaffer; Yücel, Uǧur (2012)

  In this study, elastic stress analysis of a thin circular disc made of functionally graded materials (FGMs) subjected to a temperature load and an inertia force due to rotation of the disc is investigated. Based on the two ...

• Design of hybrid composites from scrap aluminum reinforced with (SiC+TiO2+Gr+Ti+B) 

  Kurşun, Ali; Ferreira, Lygia Maria Policarpio; Bayraktar, Emin; Miskioǧlu, İbrahim (Springer New York LLC, 2017)

  Hybrid Metal Matrix Composites (HMMCs) have very light weight, high strength, and show better resistance to corrosion, oxidation, and wear. Impact resistance is an especially important property of these HMMCs which is ...

• Numerical investigation of amounts of heat, power and temperature distribution in IT-SOFC 

  Bakal, Ahmet; Kaya, Murat; Mat, Mahmut Dursun (Electrochemical Society Inc., 2013)

  In this study, thermodynamic and heat transfer concepts were combined to understanding correlation of heat, power and temperature gradient on the cell. All of heat sources and amounts has been determined for electrolyte ...

• Effects of flexural stiffness, axial velocity and internal support locations on translating beam's natural frequencies 

  Köstekci, Ferid (Trans Tech Publications, 2014)

  The aim of this paper is to examine the natural frequencies of beams for different flexural stiffness, internal simple support locations and axial moving speed. In the present investigation, the linear transverse vibrations ...

• The linear stability of the responses of axially moving beams supported by an intermediate spring 

  Köstekci, Ferid (EDP Sciences, 2016)

  In the present paper, the stability investigation of the linear responses of axially travelling beams supported by an intermediate linear spring is performed numerically by means of searching linear complex eigenvalues. ...

Daha Fazla